The replica 3317BR is a 1:1 clone watch sold under the factory code 3317BR. The code names the design, not the quality: it points to one case, dial, and bracelet set, while the movement and finishing change from seller to seller. Two watches with the same code can sit $400 apart in price and feel like different products on the wrist.
What does the code 3317BR mean?
Replica catalogs copy the naming habit of Swiss brands. Digits mark the model line and case size. Trailing letters mark the finish and bracelet type, so 'BR' in these catalogs points to a specific bracelet and metal tone.
No central registry exists for these codes. Sellers reuse them, and a code that started with one factory gets copied by others with small changes.
Treat any code as a starting point. Ask for the case diameter in millimeters, the dial colorway, and the movement name before you pay.
What movement runs inside a replica 3317BR?
Three movement tiers show up under this code. Entry listings use quartz or a basic automatic. Mid-tier listings use an Asian automatic such as a 2813, 2824, or 2836 clone. Top-tier super clone builds use a movement made to copy the original caliber layout, beat rate, and rotor engraving.
Movement choice drives price and serviceability. Some clone calibers take parts from the movement they copy, which helps any watchmaker who works on it. Others are one-piece builds that get replaced rather than repaired.
Ask for the movement name, a photo of the rotor, and the beat rate. A rate of 28,800 vibrations per hour (4 Hz) matches most Swiss automatics and gives a smooth sweep.
Pre-purchase checklist for a 3317BR clone
Case and crystal
- Case diameter and thickness: match the spec tied to the code, and confirm lug width.
- Crystal: sapphire, with a clean date magnifier and no glue halo at the edge.
- Bezel: even fluting or polishing, no tool marks, no gaps against the case.
- Case back: engraving with correct depth, and a serial that stays consistent across a factory batch.
Dial and hands
- Marker alignment at 12, 3, 6, and 9.
- Print quality on the logo and text: crisp edges, no bleeding.
- Lume color matched across dial and hands, since mismatched lume is a common tell.
- Hand length that reaches the right track, and a seconds hand that sweeps without stutter.
Bracelet and clasp
- End link fit against the case with no rattle.
- Link type: screws hold better than friction pins on a watch you plan to wear daily.
- Clasp engraving, spring bar tension, and the click on the safety lock.
Weight and feel
Gold-plated cases weigh less than solid gold originals, and that gap is easy to feel on a two-tone build. Top-tier clones sit closer to the original gram weight. Ask for a scale photo if weight matters to you.
How to match a 3317BR build to your wrist
Case size decides comfort more than any other spec. A 40 mm case with a 48 mm lug-to-lug span fits most wrists between 6.5 and 7.5 inches. Anything above 42 mm reads large on a slim wrist, and a heavy bracelet makes that worse.
Ask for the lug-to-lug measurement, not just the diameter. Sellers list diameter because it is the headline number, and lug-to-lug is the figure that decides fit.
Bracelet sizing matters too. Confirm the link count and whether spare links ship with the watch, since adding links later gets hard once a factory stops a run.
How much does a replica 3317BR cost?
Prices fall into broad bands. Entry builds sit under $100, mid-tier automatics land in the low hundreds, and top-tier super clones run from about $400 into the high hundreds. Price moves with the factory, the movement, and the seller markup.
Low price is the loudest warning sign. A listing far below the band for its movement tier points to a cheaper case, a quartz swap, or stock photos lifted from another seller.
QC photos to request before shipping
- Straight-on dial shot with the date set to a single digit.
- Case back and clasp close-ups at an angle, so engraving depth shows.
- Timegrapher photo or video showing rate, amplitude, and beat error. Aim for a rate within about 10 seconds per day and a beat error under 0.5 ms.
- Bracelet link close-up showing screws or pins.
- Lume shot in a dark room, dial and hands in one frame.
Red flags in a 3317BR listing
- No timegrapher reading, or a screenshot with the watch missing.
- Water resistance claims with no pressure test.
- Refusal to send a live date photo, since a real photo proves the watch is in hand.
- The same photos across several sellers, which points to a dropship listing.
Frequently asked questions
Is a replica 3317BR waterproof?
Water resistance depends on gaskets and assembly, not on the code. Most clones handle rain and hand washing. Swimming or diving needs a pressure test from a watchmaker, and many sellers skip that step.
Can a jeweler spot a 3317BR clone?
Yes. A trained eye checks movement finishing, case weight, dial print, and serial engraving. From across a room a good clone passes. Under a loupe, differences appear.
How long does a replica 3317BR last?
A mid-tier or super clone automatic can run for years with normal wear. Service intervals near five years help. Entry quartz builds last until the battery or the plating gives out.
Is it legal to buy a replica 3317BR?
Selling counterfeit watches is illegal in the United States. Importing one risks seizure by customs, and repeat shipments can bring fines. Rules differ by country, so check local law before you order.
What to do with this guide
Pick the movement tier first, then the build. Confirm the case spec and dial photos, request a timegrapher reading, and pay once the QC set looks clean. The code gets you to the right listing, and the checks decide whether the watch is worth the money.